ADBLUE EURO6 Emulator for MAN/BENZ/DAF/IVECO/SCANIA/VOLVO

Description

You will get PDF Manual book for connection wires.

Why we need buy Adblue EURO6 Emulator for Trucks ?

Trucks generally give adblue or Nox system faults so working hard. Your truck may loss torque so some adblue faults or fault lamps. These problems cause you to lose money and time.
After the installiation adblue remove emulator, you dont get another adblue faults and you dont need add adblue fuel.
And your adblue fuel level will up automaticly.

Adblue Remove emulator disable these systems

• AdxBlue system (All)
• AdxBlue NOX sensor
• DPF system
• DPF temperature sensors
• DPF regeneration

ADBLUE EURO6 Emulator for Scania ：

Not need to be leaming, you have to mount emulator in the plug of the EEC(AdBlue)ECU(in the pink one),Yon can find EEC ecu ta the center of the vehicle frame.Two big plugs(one is pink) in this manual you will find pin mumber of the EEC plug,also colours cables of EEC and Emulator.

Connect wires of the emulator with this table as reference:

• Red(Vcc)-PIN 12 (green) Cut the cable after connect emulator to truck side
• Black (GND)-PIN 4 (fat black)
• Yellow (CAN H）-PIN 22 （orange)
• Green (CAN l)-PIN 19 (fat black)

AdBlue Emulator Installation For Mercedes Benz EURO6：

1. Behind fuses in the middle is a plug- as in the price (not right like in manual-correct is middle)
2. Connnection colors-White(Emulator side) with Blue (Truck side) with White (Truck side)
3. Red wire from emulator connection with any(+)after ignition
4. Black i GND
5. Next step is remove Fuse
6. F23 Thats all

For Mercedes Atego Euro 6 AdBlue Remove Emulator Installation：

1. You must locate the ACm Module and remove the socket.
2. The cable should be installed as shown in the picture below:
   Emulator White cable(CAN H) —–>Atego vehicle socket 10 pin(CAN H)
   Emulator Brown cable (CAN L) —–> Atego vehicle socket 20 pin (CAN L)
   Emulator Red (+) —–>Atego vehicle Positive(+)Cable
   Emulator Black(-) —–>Atego vehicle GND (-)
3. After installation, you must remove errors with obd2 diagnosis tools.
4. You will not mount the socket back into the ACM module Isolate the Atego ACh nodule without damage.
5. You should definitely cancel the DPF after installing the AdBlue Removal Emulator：

MAN ADBLUE EURO6 Emulator using guide :

Emulator For MAN Euro 6 does not need to be learned. You install emulator under the metal cover of AdBlue Pump on the right side behind the cab, and disconnect plug from AdBlue Pump and connect emulator.Next, you need to remove the fuses:

• F894(Multisensor In AdBlue tank)
• F738 (+30 Signal of AdBlue pump)
• F1084 (NOx sensor Upstream)
• Fuse F737 is now fuse of emulator.
• Fuse F1109 is the fuse of NOx sensor Downstream and A1191 mufler temperature sensor. This sensor needs to work correctly for DPF regeneration.

Finally, you need to remove Power from NOx downstream sensor. There are two ways options, one is to cut pin 1 in NOx sensor plug, the other way (better) is to remove pin 10 in X3212 plug. This plug is visible on rear of engine on the right side. This is TE plug (16 pin) with yellow key.