//Toyota Remote Key programmer for G/H Chip,add Remote,Transponder

Toyota Remote Key programmer for G/H Chip,add Remote,Transponder

$17.60

Description

Toyota Remote Key programmer is one cheap and easy device that for add Transponder key and Remote Control.it support both G and H chip,Apply to 4D67,68,72(G) chip. This toyota key Tool not support all keys lost programming .

How to Add Remote Control by this Toyota G/H Key Programmer ?
(Switch should on the right )

Get in the car and close the door, insert the key and turn the key on, insert the device into OBD. After the sound(Dee-), it will start to add the remote control.
After the sound ( Dee- Dee-),open the door, when hear the sound blaring. Press ‘ lock & unlock’ key at the same time. And press the’ lock’ key. If the blaring end, It’s OK.

How to Add Toyota Transponder key ?
(Switch should on the Left )

Get in the car and close the door, insert the main key into the lock and turn the key on,and then insert the device into the OBD. If it will sound twice, it will start to add transponder.
After the sound (Dee-Dee-), 2-3 minutes later, anti-theft light is on. And then remove the key( anti-theft light will flash), insert the new key and doesn’t need turn the key,
anti-theft light will be off later.

Toyota Remote Key programmer Reviews:

1. I have a 2015 camry. i was able to program the key (g chip) fine but the keyfob process doesn’t seem to work. After i tried Use Techstream interface and software adapted it.

2.Programmed 3 transponder Keys (type g) and 2 fobs/remotes.
Here are the key/transponder steps for my 2012 Toyota Sienna:
Turn programming tool switch to transponder (key). Close drivers door. Start engine with master key. Insert programmer tool into OBDII port, 2 short beeps follow. After about 10 seconds there is a Long nearly constant beep(s) for about 5 seconds. Wait for the Anti theft light to turned solid. Then remove master key (turns engine off). Then insert new key into ignition, don’t turn the key. The anti-theft light will start flashing. After about 45 seconds the anti theft light turns off completely. Your transponder key is programmed. Remove new key (security light starts flashing because anti theft system is armed). Remove programmer. Check new key by starting engine.

3.I have a 2017 Toyota Highlander. While the instructions on the device are not that great, the device works. Actually to program the key chip, it didn’t take the 2-3 mins as described on the instructions (took about 1 min). Same with the remote fob on the key, it took less then about 1 min. I think I went through the steps a couple of times (because I screwed up initially)

4.I have a 2014 Camry SE. I had two keys to program.
I first programmed the transponder in each key following the instructions and it worked with no issues.
I removed the Toyota Remote Key programmer from the port after programming each key’s transponder. I then began to program the remote part of the keys.
The first time it did not work and I realized I forgot to move the switch on the programmer. After moving the switch and following the instructions for programming the remote portion it worked like a charm. I made sure to test all the buttons on the remote and all functioned properly. The Toyota dealer wanted $215 for a (1) new key and $70 to program and cut it. I bought 2 new keys on Amazon for $43 and this device for $42. That’s a savings of $485 compared to the dealership. I still have to have the keys cut. I est that should be and additional $20. I did knock off a star for the small and light instruction printing on the device.

 

Reviews

There are no reviews yet.

Be the first to review “Toyota Remote Key programmer for G/H Chip,add Remote,Transponder”

Your email address will not be published. Required fields are marked *

0
    0
    Your Cart
    Your cart is emptyReturn to Shop